We've encountered this article about A Step-by-Step Guide to Installing a Bathtub below on the net and felt it made good sense to relate it with you in this article.
Mounting a bath tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is easily available, the job can move rapidly; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This post will assist you install a new bath tub in your shower room if you have currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bathtub and additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub should wait till the bath tub has actually been utilized a minimum of once as this will certainly resolve it right into its final position.
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealant can fracture fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on How to Install a Bathtub. Thanks a ton for taking a few minutes to read our content. Enjoyed our piece? Please share it. Help another person find it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book My Estimate